Mm Manual
Introduction This is a manual for working with the DynaPort MM. It is recommended to follow the steps in this manual prior to the first measurement to familiarize yourself with the device and its settings. With the index on the left hand side of this page you can quickly navigate to the paragraph of interest. The manual for working with the USB DynaPort (Serial numbers UD2010xxxx and UD2012xxxx) can be found. Before first use The DynaPort MM can be controlled via the website.
All steps, from preparing the measurement to viewing the reports take place here. Download installer After your first login a pop-up will appear with the request to download a small software package. Download this software in order to establish a connection between your DynaPort MM device(s) and the software on My McRoberts. Please follow the wizard to install the software.
Gr2150901-mm Manual
This needs to be done for each computer that you use the DynaPort MM on. Preparing the device for a measurement Charging the device It is important to charge the DynaPort MM to ensure maximal measurement capacity. If the battery runs empty during the measurement, the measurement will prematurely stop.
How to charge. Select measurement characteristics Select the starting time of the measurement; this can either be now or up to 7 days later. Thereafter, a measurement duration should be selected.
The maximal measurement duration is 14 full days. Project and subject characteristics Add or select a project, subject and visit in order to start a measurement. Using different projects is useful for organizing your data. Subject characteristics have to be added for each new subject.
Visits refer to different measuring moments. If there is only one measuring moment (visit), fill in a random number as visit number and in the future this visit number will appear as a default setting. The device can be started with the Start measurement-button when all the necessary information for a new measurement has been supplied.
The device can be disconnected from the computer when the program notifies you to do so. After disconnecting, the LEDs will blink for about 10 seconds after which the DynaPort MM will go into standby mode. When the selected start time is reached the DynaPort MM will start measuring. During the first 5 minutes of the measurement the green LED will blink. When data of a previous measurement is found on the device the program will ask to format the device prior to starting a new measurement. Note that formatting the device removes all data from the DynaPort MM.
When the data from the previous measurement has already been uploaded to the MyMcRoberts web portal your data is save and removing it from the device is recommended. Click on a status to view the individual measurements belonging to that status. The number in each status tab shows how many measurements have that particular status. Each measurement status will be explained below. Measuring All measurements that are currently being performed are shown here. This overview shows the time left until a certain measurement has finished and it shows when a measurement is 'ready for upload'.
In that case you only have to couple your DynaPort MM to the PC to start the upload. Analysing Measurements that have just been uploaded are displayed under the 'Analysing' tab until the analysis of this measurement is completed.
Mmm Annual Dividend Yield
Analysis completed When the analysis of a measurement is completed and reports are ready to be viewed, the measurement is displayed under the 'Analysis completed' tab. Click on a measurement to view or download the reports.
All reports for which you have purchased a license are visible here. Analysis failed When the software fails to analyse a measurement it will be displayed under the 'Analysis failed' tab'. The McRoberts Support Team will be notified of such an analysis failure and will fix the problem or otherwise contact you.
Idle measurements Any measurement that's not in any of the categories above is considered 'idle' and will be shown here. This is usually because you don't have the appropriate licenses to start analysis. Contact McRoberts if you wish to take further actions. Project data.
Manual Slides and Stages - MM Series Stages from Parker Hannifin Motion Control Systems, Electromechanical Automation, North America: MM Series Stages MM Series Stages The Micro-Mini (MM) Series offers our most compact manual positioner available. Available in single and multi-axis units the MM Series is ideal for fine adjustment in a compact environment. 16 mm wide. 5 mm tall. 12 oz load carrying capacity Price, Real Time Availability and On-line Ordering: Additional products to build your total Parker solution: Manual Slides and Stages Ball Screw and Lead Screw Tables Ball Screw and Lead Screw Tables Miniature Linear Stages Miniature Linear Stages MM Series Stages Other Products in This Category: Manual Slides and Stages Ball Bearing Stages Bearing Type Max. Load (lbs) Max. Travel (in) Width (in) Ball Bearing 0.75 0.5 0.44 Ball Bearing 6 0.5 1.25 Ball Bearing 123 2.0 1.75 - 5.00 Ball Bearing 294 12 6 Catalog and Specifications.
User Guides. Download - Drawings and CAD files. Publications and Advertisements. Support. Engineering Tools. Contact Us TEL: (707) 584 7558 or (800) 358 9070 FAX: (707) 584-3793 IPS Structural Aluminum TEL: (330) 335 6740 (800) 333 4932 FAX: (330) 334 2350 Included part numbers in this series (click on the part below to buy online now), ©Copyright Parker Hannifin Corporation 2003-2009.